Power Tools

• 200Lt 3HP Single-Stage Compressor

• Option for Shamal or Nauair available for this model not available.

Important - there is also the ABAC brand for the same model at an additional cost of 20% currently in stock.

• Twin drill bit made of high speed steel
• Manufactured to DIN338
• Right-hand cutting twist drill bit, Type N, 135° drill bit tip, split point manufactured to DIN 1412 C, diameter tolerance h 8
• Shank equal to drill bit diameter
• Two-cutter, cylindrical, two flutes
• Suitable for alloyed and non-alloyed steel up to a tensile strength of 900 N/mm², cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics
• Precision ground - enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with a chisel edge
• Self centering split point drill tip means there is no need to pre-punch or pilot drill up to 10mm diameter
• Note: Use the universal cutting oil (2 607 001 409) when working with HSS-G metal drill bits
• Pack of 10

• Twin drill bit made of high speed steel

• Manufactured to DIN338

• Right-hand cutting twist drill bit, Type N, 135° drill bit tip, split point manufactured to DIN 1412 C, diameter tolerance h 8

• Shank equal to drill bit diameter

• Two-cutter, cylindrical, two flutes

• Suitable for alloyed and non-alloyed steel up to a tensile strength of 900 N/mm², cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics

• Precision ground - enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with a chisel edge

• Self centering split point drill tip means there is no need to pre-punch or pilot drill up to 10mm diameter

• Note: Use the universal cutting oil (2 607 001 409) when working with HSS-G metal drill bits

• Pack of 10

• Twin drill bit made of high speed steel

• Manufactured to DIN338

• Right-hand cutting twist drill bit, Type N, 135° drill bit tip, split point manufactured to DIN 1412 C, diameter tolerance h 8

• Shank equal to drill bit diameter

• Two-cutter, cylindrical, two flutes

• Suitable for alloyed and non-alloyed steel up to a tensile strength of 900 N/mm², cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics

• Precision ground - enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with a chisel edge

• Self centering split point drill tip means there is no need to pre-punch or pilot drill up to 10mm diameter

• Note: Use the universal cutting oil (2 607 001 409) when working with HSS-G metal drill bits

• Pack of 10

• For sheet metal 10-16 gauge, thin metals 1/16 In. to 1/8 In. thick (ferrous and non-ferrous)
• 17-24 TPI progressive tooth design for smooth cuts in various thicknesses
• High-speed steel construction for maximum life in straight cuts
• 3-5/8 In. overall length, 2-5/8 In. working length
• Proper lubricant is recommended when cutting metal
• 5 piece pack

• Perfectly suited to cutting parquet, laminate, expoxy, glass fibre and cement-bonded fibre boards
• Very fine cut in plastic and non-ferrous metals
• Base Blade, dimensionally stable SK5 steel, hardened (>40 HRC)
• Tungsten carbide teeth
• Safe cuts thanks to negative (-5°) trapezoidal/flat teeth made of high-quality tungsten carbide
• Body and expansion slots lower vibrations, dampen noise and reduce heat development

• Suitable for alloyed and non-alloyed steel up to a tensile strength of 1000 N/mm², stainless steel V2A/V4A, cast iron, cast steel, acid and heat-resistant steels.
• Precision drill bits that are resistant to heat and wear.
• For use in drill stands or in pillar drills.
• The HSS-G drill bits are available in two qualities.
• The Topline drill bits are for the highest requirements and the standard drill bits are for professional use.

• Narrwo Crown Staple box of 5000pcs
• 30G 1.2/18g. 
• There are also avaiable these models: 20G 1.2/18g and 15G 1.2/18g.
• So customer can indicate the particular measurement of choice. 

•  Brad nailers are ideal for trim work and allow you to more easily reach tight spaces, improve nailing accuracy, and reduce work surface damage.
• There are available 15mm, 20mm, 25mm, 30mm and 35mm in stock.
• Customers are allowed to choose sizes before shipment. 

• Highest material removal rate and cutting performance in its class per battery charge
• Compact design and low weight (only 2.3 kg) for comfortable working, especially in tight spaces and overhead
• Innovative CoolPack batteries ensure optimum heat dissipation and therefore increase lifetime by up to 100% (cf. Li-Ion batteries without CoolPack)
• Practical battery charge level indicator: constantly shows how much energy is left in the battery
• Handle can be used on right or left
• No memory effect: the battery can be charged regardless of the charging state at any time, without damaging the cells

• Extremely robust and durable 4-pole high-performance motor for a long lifetime
• Bosch Electronic Cell Protection (ECP): protects the battery against overload, overheating and deep discharge
• Bosch Electronic Motor Protection (EMP) protects the motor against overload and ensures a long lifetime
• Gear head can be rotated in 90 degree steps
• Anti-rotation protective guard – quickly and easily adjustable, provides reliable protection